It needs to be established in the right place for the work and environment of the greenhouse. The slope for drainage is an important element.
There should be a need to channel the surface water out of the greenhouse. There is a need for some time to carry the goods inside and outside the greenhouse.
If you are near any market then you have more comfort. Dry water is another important factor in demand. It should always be constructed.
Remove the greenhouse from the surrounding buildings and shrines to prevent the sun from spreading.
It is better to place in the east and west direction in order to get better lighting during the cold season than in the south of the south.
Many factors need to be considered regarding the construction of greenhouses. The most important of these are the correct position of the structure, the availability of air, the maximum amount of sunlight and the whole night
Order: 2
LPPE with the help of polypropylene stool after bitumen (charcoal) in large wooden poles. Wrap the film. This is not to be left behind.
In the picture, a good frame is made of a good basin with a good wind turbine. Fix the framework with buds as seen in the picture.
Pour the soil out of 0.2 m x 0.2 m in the greenhouse. Controlled LDPE The edges of the film can be used to cover the edges.
Notice that the soil does not have rocks, rocks, rocks, objects still today. UV Controlled LDPE All the factions that are likely to interact with the film are in the LDPE. Wrap the film roll. Any of the sharp areas are UV's.
Controlled LDPE This is to avoid touching the film. If not, the sheet will be damaged and the dust and residue from the wood will lose the quality of the film.
Wrap the film roll in the beds' attachment (see picture), especially UV's. Regulated LDPE Everywhere you need contact with the film. The sharp sides of the joints are UV's.
Regulated LDPE The powder and stain on the basins will be damaged in the film to avoid contact with the film. It can also be prevented.
As shown in the picture below, UV's Regulated LDPE Flip over the film frame. Make sure the rubber washer nail at 2 '' two edges in width and 4 ''.
Place the sheet down to the ditch below. Front and backs of LDPE Cover the sheet with the sheets and cut off the sheet.
Add them to the mold. Cover the sheets onto the corners and cover the soil. Fill the soil thoroughly, except on both sides of the entrance door. HDPE in the entrance door. The sheet can be folded up or down.
The sheet can be placed on the top of the entrance door, as shown in the picture.
There should be a need to channel the surface water out of the greenhouse. There is a need for some time to carry the goods inside and outside the greenhouse.
If you are near any market then you have more comfort. Dry water is another important factor in demand. It should always be constructed.
Remove the greenhouse from the surrounding buildings and shrines to prevent the sun from spreading.
It is better to place in the east and west direction in order to get better lighting during the cold season than in the south of the south.
Many factors need to be considered regarding the construction of greenhouses. The most important of these are the correct position of the structure, the availability of air, the maximum amount of sunlight and the whole night
Order: 2
LPPE with the help of polypropylene stool after bitumen (charcoal) in large wooden poles. Wrap the film. This is not to be left behind.
In the picture, a good frame is made of a good basin with a good wind turbine. Fix the framework with buds as seen in the picture.
Pour the soil out of 0.2 m x 0.2 m in the greenhouse. Controlled LDPE The edges of the film can be used to cover the edges.
Notice that the soil does not have rocks, rocks, rocks, objects still today. UV Controlled LDPE All the factions that are likely to interact with the film are in the LDPE. Wrap the film roll. Any of the sharp areas are UV's.
Controlled LDPE This is to avoid touching the film. If not, the sheet will be damaged and the dust and residue from the wood will lose the quality of the film.
Wrap the film roll in the beds' attachment (see picture), especially UV's. Regulated LDPE Everywhere you need contact with the film. The sharp sides of the joints are UV's.
Regulated LDPE The powder and stain on the basins will be damaged in the film to avoid contact with the film. It can also be prevented.
As shown in the picture below, UV's Regulated LDPE Flip over the film frame. Make sure the rubber washer nail at 2 '' two edges in width and 4 ''.
Place the sheet down to the ditch below. Front and backs of LDPE Cover the sheet with the sheets and cut off the sheet.
Add them to the mold. Cover the sheets onto the corners and cover the soil. Fill the soil thoroughly, except on both sides of the entrance door. HDPE in the entrance door. The sheet can be folded up or down.
The sheet can be placed on the top of the entrance door, as shown in the picture.
